App health checks
The app health checks feature allows probing for the health of your application and reacting to status changes.
Applications can become unresponsive for a variety of reasons. For example, your application:
- Could be too busy to accept new work;
- Could have crashed; or
- Could be in a deadlock state.
Sometimes the condition can be transitory, for example:
- If the app is just busy and will resume accepting new work eventually
- If the application is being restarted for whatever reason and is in its initialization phase
App health checks are disabled by default. Once you enable app health checks, the Dapr runtime (sidecar) periodically polls your application via HTTP or gRPC calls. When it detects a failure in the app’s health, Dapr stops accepting new work on behalf of the application by:
- Unsubscribing from all pub/sub subscriptions
- Stopping all input bindings
- Short-circuiting all service-invocation requests, which terminate in the Dapr runtime and are not forwarded to the application
These changes are meant to be temporary, and Dapr resumes normal operations once it detects that the application is responsive again.
App health checks vs platform-level health checks
App health checks in Dapr are meant to be complementary to, and not replace, any platform-level health checks, like liveness probes when running on Kubernetes.
Platform-level health checks (or liveness probes) generally ensure that the application is running, and cause the platform to restart the application in case of failures.
Unlike platform-level health checks, Dapr’s app health checks focus on pausing work to an application that is currently unable to accept it, but is expected to be able to resume accepting work eventually. Goals include:
- Not bringing more load to an application that is already overloaded.
- Do the “polite” thing by not taking messages from queues, bindings, or pub/sub brokers when Dapr knows the application won’t be able to process them.
In this regard, Dapr’s app health checks are “softer”, waiting for an application to be able to process work, rather than terminating the running process in a “hard” way.
NoteFor Kubernetes, a failing app health check won’t remove a pod from service discovery: this remains the responsibility of the Kubernetes liveness probe, not Dapr.
Configuring app health checks
App health checks are disabled by default, but can be enabled with either:
--enable-app-health-checkCLI flag; or
dapr.io/enable-app-health-check: trueannotation when running on Kubernetes.
Adding this flag is both necessary and sufficient to enable app health checks with the default options.
The full list of options are listed in this table:
|Kubernetes deployment annotation
|Boolean that enables the health checks
|Path that Dapr invokes for health probes when the app channel is HTTP (this value is ignored if the app channel is using gRPC)
|Number of seconds between each health probe
|Timeout in milliseconds for health probe requests
|Max number of consecutive failures before the app is considered unhealthy
See the full Dapr arguments and annotations reference for all options and how to enable them.
Additionally, app health checks are impacted by the protocol used for the app channel, which is configured with the following flag or annotation:
|Kubernetes deployment annotation
|Protocol used for the app channel. supported values are
h2c (HTTP/2 Cleartext).
NoteA low app health probe timeout value can classify an application as unhealthy if it experiences a sudden high load, causing the response time to degrade. If this happens, increase the
Health check paths
When using HTTP (including
app-protocol, Dapr performs health probes by making an HTTP call to the path specified in
app-health-check-path, which is
/health by default.
For your app to be considered healthy, the response must have an HTTP status code in the 200-299 range. Any other status code is considered a failure. Dapr is only concerned with the status code of the response, and ignores any response header or body.
When using gRPC for the app channel (
app-protocol set to
grpcs), Dapr invokes the method
/dapr.proto.runtime.v1.AppCallbackHealthCheck/HealthCheck in your application. Most likely, you will use a Dapr SDK to implement the handler for this method.
While responding to a health probe request, your app may decide to perform additional internal health checks to determine if it’s ready to process work from the Dapr runtime. However, this is not required; it’s a choice that depends on your application’s needs.
Intervals, timeouts, and thresholds
By default, when app health checks are enabled, Dapr probes your application every 5 seconds. You can configure the interval, in seconds, with
app-health-probe-interval. These probes happen regularly, regardless of whether your application is healthy or not.
When the Dapr runtime (sidecar) is initially started, Dapr waits for a successful health probe before considering the app healthy. This means that pub/sub subscriptions, input bindings, and service invocation requests won’t be enabled for your application until this first health check is complete and successful.
Health probe requests are considered successful if the application sends a successful response (as explained above) within the timeout configured in
app-health-probe-timeout. The default value is 500, corresponding to 500 milliseconds (half a second).
Before Dapr considers an app to have entered an unhealthy state, it will wait for
app-health-threshold consecutive failures, whose default value is 3. This default value means that your application must fail health probes 3 times in a row to be considered unhealthy.
If you set the threshold to 1, any failure causes Dapr to assume your app is unhealthy and will stop delivering work to it.
A threshold greater than 1 can help exclude transient failures due to external circumstances. The right value for your application depends on your requirements.
Thresholds only apply to failures. A single successful response is enough for Dapr to consider your app to be healthy and resume normal operations.
Use the CLI flags with the
dapr run command to enable app health checks:
dapr run \
--app-id my-app \
--app-port 7001 \
--app-protocol http \
--app-health-probe-interval 3 \
--app-health-probe-timeout 200 \
--app-health-threshold 2 \
<command to execute>
To enable app health checks in Kubernetes, add the relevant annotations to your Deployment:
Watch this video for an overview of using app health checks:
Was this page helpful?
Glad to hear it! Please tell us how we can improve.
Sorry to hear that. Please tell us how we can improve.